Power Quality Analyzer Fluke 43B

Power Quality Analyzer Fluke 43B Specifications Input Characteristics Input impedance 1 M© , 20 pF Voltage rating 600V rms, CAT III V/ A/ Hz Display True-rms voltage ( ac + dc) Ranges: 5.000 V, 50.00 V, 500.0 V, 1250 V* Accuracy: ± ( 1% + 10 counts) True-rms current ( ac + dc) Ranges: 50.00 A, 500.0 A, 5.000 kA, 50.00 kA, 1250 kA Accuracy: ± ( 1% + 10 counts) Frequency Ranges: 10.0 to 15.0 kHz Accuracy: ± ( [ % of reading] + [ counts] ) : 0.5% + 2 CF Crest factor Ranges: 1.0 - 10.0 Accuracy: ± ( 5% + 1 count) Power Display Watts, VA, VAR 1-phase and 3-phase, 3 conductor balanced loads Ranges: 250 W - 1.56 GW Accuracy: ± ( 4% + 4 counts) Fundamental Power Accuracy: ± ( 2 % + 6 counts) Total Power PF Power Factor Range: 0 - 1.0 Accuracy: ± 0.04 DPF Displacement Power Factor, Cos .F Range: 0.25 - 0.9 Accuracy: ± 0.04 Range: 0.90 - 1.0 Accuracy: ± 0.03 H2 Frequency Fundamental Ranges: 40.0 to 70.0 Hz Accuracy: ± ( [ % of reading] + [ counts] ) : 0.5% + 2 Harmonics Display Voltage, Current, Frequency Ranges: Fundamental to 51st harmonic Accuracy: Fundamental: VA ± ( 3% + 2 counts) W ± ( 5% + 2 counts) 2 to 31st harmonic: VA ± ( 5% + 3 counts) W ± ( 10% + 10 counts) 32 to 51st harmonic: VA ± ( 15% + 5 counts) W ± ( 30% + 5 counts Frequency Fundamental Ranges: 40 Hz to 70 Hz Accuracy: ± 0.25 Hz Phase Range: V, A ( between Fundamental & Harmonics) Accuracy: ± 3º to ± 15º Range: W ( between Voltage Fundamental & Current Harmonics) Accuracy: ± 5º to ± 15º K-factor ( Current and Power) Range: 1.0 to 30.0 Accuracy: ± 10% THD Total Harmonic Distortion Range: 0.00 - 99.99 Accuracy: ± ( 3% + 8 counts) Sags and Swells Recording times: 4 min to 16 days ( selectable) Vrms Actual, Vrms max, min( AC + DC) Ranges: 5.000V, 50.00V, 500.0V, 1250V* Accuracy: Readings ± ( 2% + 10 counts) ; Cursor readings ± ( 2% + 12 counts) Arms Actual, Arms max, min ( AC + DC) Ranges: 50.00A, 500.0A, 5.000 kA, 50.00 kA Accuracy: ± ( 2% + 10 counts) Transient Capture Minimum pulse width: 40 ns Useful bandwidth input 1: DC to 1 MHz Number of transients: 40 Voltage threshold settings: 20% , 50% , 100% , 200% above or below reference Reference signal: After START, the Vrms and frequency of the signal are measured. From these data a pure sinewave is calculated as reference for threshold setting. Vpeak min, Vpeak max at cursor: 10 V, 25 V, 50 V, 125 V, 250 V, 500 V, 1250 V Accuracy: ± 5% of full scale R, C, Diode, Continuity Resistance ranges: 500.0 © , 5.000 k© , 50.00 k© , 500.0 k© , 5.000 M© , 30.00 M© Resistance accuracy: ± ( 0.6% + 5 counts) Capacitance ranges: 50.00 nF, 500.0 nF, 5.000 µ F, 50.00 µ F, 500.0 µ F Capacitance accuracy: ± ( 2% + 10 counts) Diode Ranges: 0 to 3.000 V Diode voltage: Accuracy: ± ( 2% + 5 counts) Continuity: Beeper on at < 30 © ± 5 © Max current: 0.5 mA Temperature: ° C or ° F Inrush Current Inrush times: 1 s, 5 s, 10 s, 50 s, 100 s, 5 min Current ranges: 1 A, 5 A, 10 A, 50 A, 100 A, 500 A, 1000 A Cursor readings: A peak max at cursor 1 and cursor 2 Accuracy: ± 5% of full scale Time between cursors: 4 to 235 pixels ( 1 pixel = inrush time/ 250) Accuracy: ± ( 0.2% + 2 pixels) Temperature ( with accessory) Range: -100 ° C - 400 ° C Accuracy: ± ( 0.5% + 5 counts) Scope Display Measurements: dc, ac, ac+ dc, peak, peak-peak, frequency, duty cycle, phase, pulse width, crest factor Time ranges: 20 ns/ div to 60 s/ div Max sampling rate: 25 MS/ s Bandwidth Voltage channel [ 1] : 20 MHz at inputs, 1 MHz with TL24 Leads Current channel [ 2] : DC to 15 kHz at inputs, 10 kHz with i400s Current Clamp Coupling: AC, DC ( 10 Hz - 3 dB) Vertical sensitivity: 5 mV/ div to 500V/ div Vertical resolution: 8 bit ( 256 levels) Record length: 512 samples per channel Base ranges: 60 S/ div to 20 nS/ div ± ( 0.4% + 1 pixel) Timebase modes: Normal, roll, single Pre-trigger: Up to 10 divisions Trigger Source: Input 1 or Input 2 or automatic selection Trigger Mode: Automatic Connect-and-View™ , Free Run, and Single Shot Connect-and-View™ : Advanced automatic triggering that recognizes signal patterns Automatically adjusts triggering, timebase and amplitude and displays stable pictures Memories 20 ( screens, settings, data) Recording Recording times: 4 min to 16 days ( selectable) Parameters: Choose one or two parameters from one of the groups below: Volts/ Ampè res/ Hertz Power: Watts, VA, VAR, PF, DPF, Frequency Harmonics, THD, Volts ( Fund. & Harmonic) , Ampè res ( F& H) Watts( F& H) Frequency ( H) , % ( H) of total, Phase( H) , KF Temperature Resistance: Resistance, Diode, Continuity, Capacitance Scope: DC Voltage, DC Current, AC Voltage, AC Current, Frequency, Pulse Width + or -, Phase, Duty cycle + or -, Peak max, Peak min, Peak min-max, Crest Factor Note * Rated EN 61010-1 600 V CAT III CSA